Xfly 25g Digital Mg Servo Positive With 900mm Lead 
Xfly 9g Digital Mg Servo Positive With 50mm Lead 
Xfly 9g Digital Servo Positive With 400mm Lead 
Xfly 100a Brushless Esc 
Xfly 9g Digital Gear Servo Positive With 100mm Lead 
Kyosho 1:18 Lamborghini Countach Lp500r Black-White 
1:8 Buggy STORM SOFT "V2" pre-mounted white (2) 
Xfly 9g Digital Mg Servo Positive With 700mm Lead 
Xfly 13g Digital Mg Servo 25t Reverse With 100mm Lead 
Xfly 64mm T-7a Red Hawk Edf Jet 750mm Without Tx/Rx/Batt 
Jetko Ex Couragia 1/10 Touring/Rally Tyre Black Wheel 12mm Hex (4) 
Xfly 25g Digital Mg Servo Positive With 300mm Lead 
1:8 Buggy WIND SUPER SOFT "V2" pre-mounted yellow (2) 
Hex Adaptor 24mm for Xmaxx Extreme Wheels (4) 
Xfly 20a Brushless Esc 
Xfly 50a Brushless Esc 
Xfly 20a Brushless Esc With Xt30 Plug 
Xfly Twin Edf 70mm B-1b Lancer Without Tx/Rx/Battery 
Xfly 20a Brushless Esc*2 With Xt60 Plug 
Xfly Glastar V2 Bush/Trainer 1233mm Wingspan Without Tx/Rx/Batt 
Xfly 13g Digital Metal Gear Servo Reverse With 100mm Lead 
Key Specs
About this product
ABSIMA FIRST STEP PERFORMANCE
Discover the RC model sport with the “First Step Performance” from Absima. More than 35 KM/H and power to the max you will get with this awesome model. Of course you will be supported by real RC model technique. A safe 2.4 GHz remote control system supports the 30A electronic speed controller to release the power at your command. Small, fine, and mean! Take the first step into the world of RC model sport with this ready-to-run set.
Highlights:
+ 35 KM/H
Splash water protected by complete chassis cover
Incl. 7.4V Li-ion battery and USB charging cable
Many parts exchangeable
General Chassis Features:
4WD
Metal wheel shaft with oil bearings
Differentials with ring & pinion gears (ball bearings)
380 brushed motor
30A speed controller/receiver unit
2kg steering servo (5 line)
Shock absorbers
Metal drive shafts
Radio range: up to 60m
Battery life time: up to 20 Minuten
Aluminum cardan drive shaft
Overheat protection
2.4 GHz radio system
Transmission ratio: 15:1
30° Steering angle (proportional)
Covered chassis and electronic parts
7.4V 1200mAh Li-Ion car battery
Radio battery: 3* AA batteries (not included)
Technical Specification:
Dimmension (L/W/H): 255 x 180 x 110 mm
Weight: 616 g (incl. battery)
Wheelbase: 165 mm
Ground clearance: 26 mm
Track width: 150 mm front / 150 mm rear
Wheel design: Sand Reef / 5 Spokes
Front wheels: Width 36 mm / Ø ± 65 mm
Rear wheels: Width 36 mm / Ø ± 65 mm
Dämpferöl Viskosität : n.a.
Shock spring force : Soft
Shock mounting size: 60 mm front / rear
Scope of delivery:
1/18 RC Car
2.4 GHz radio system
Car battery
USB charging cable
Manual with spare part list
Required accessories:
3x AA cells for radio
Frequently Asked Questions
The CR3.4 SHERPA is designed as a ready-to-run (RTR) model suitable for beginners, though it's also capable enough for experienced drivers. It comes fully assembled with everything needed to drive straight from the box, making it an ideal entry point into RC crawling.
The set includes a 7.4V 1200mAh Li-Ion battery with a USB charging cable. For exact charge times, you should check the manual, as this varies depending on your charger.
The box contains the assembled 1:10 RC crawler, a 2.4GHz radio system, a 7.4V 1200mAh Li-Ion battery, a USB charging cable, and a manual with spare parts list. Note that the radio requires 3x AA batteries, which are not included.
The CR3.4 measures 255 x 180 x 110 mm and weighs 616g with battery installed. It delivers approximately 20 minutes of runtime per charge on the included battery.
The SHERPA reaches 35 km/h and features a splash water-resistant design with a complete chassis cover protecting the electronics. It's suitable for wet terrain but not fully waterproof submersion.
